Chosen Solution Can anyone help ? The Behringer speaker works ,however the 22ohm resistor R4 which is in series with capacitor C23 gets really hot and begins to smell Also i Noticed when measured resistance of woofer it measures 6ohms(When it is labelled 8ohms on speaker) could this affect the amplifier? You could wait until R4 catches fire. Or you could replace it now along with the C23 just to be safe....
Chosen Solution When I plug the charger in the power light blinks and also 3 of the little lights on the bottom blink also. When the charger is not plugged in the lights doesn’t blink. Also if I push the charger in harder to make it work my laptop shuts off. I have an Acer Swift 1. It too conked out with black screen and unable to repower. I found an easy solution for my case....
Chosen Solution blue veritical line on lcd screeen The vertical strips are dead pixels. That being said a cable could be torn messed up inside your device and so on. Is this a tv a computer or what? anusha, a single vertical line is usually caused by a TAB eror. Check your signal cables to make sure it is properly seated. If it is, the LCD needs to be replaced to get rid of that line....
Chosen Solution I have a Bose AV35 control console which is stuck on green blinking light. The green blinking light mean the system is starting, but the light doesn’t turns to solid green ever. Other observation is No output to display or to sub-woofer module. I tried resetting the system no luck. Any one know whats happening in there. . . . . It happened to me. It was an issue with the main board due to over voltage via HDMI port....
Chosen Solution hi, i snapped the thin flex cable for the power button when trying to replace the screen. is there a part i can replace? or will soldering work? Soldering skills of medium level will be required and a good iron with small tip (silver bearing (preferred) solder with good non acid flux as well). I would not advise anyone who does not have those skills to attempt repair unless you don’t mind F@i& up the whole board....
Chosen Solution My iPhone 6 recently started having cellular issues, I put my sim in and it says no service, so I repeatedly take it out and put it back, which then displays my network with no signal bars. I try to make a call and it says failed. Any ideas thanks Have you restarted the phone? If you haven’t, try that. You could also try a hard reset, hold the power and home buttons until the phone shuts off and keep holding until the Apple logo comes back on....
Chosen Solution My nikon D5100 only works in live mode and I am not sure how to repair it it may be that the mirror has fallen out. IF mirror has no issues, then there are two chances : Auto focus sensor has problem (Located below the mirror - bottom side of camera ) Prism assembly has problem
Chosen Solution My hard drive cable must be shot and is having the same problem I’ve found with others. Instead of having someone charge me over $100 to replace this, I’d rather do it myself. My hard drive cable’s apple number is: 821-00698-A and I can’t find one of those really anywhere (unless I don’t know where to look). Is it a bad decision to order a cable that has a different serial/apple number than the one I currently have?...
Chosen Solution Good afternoon, I do a lot of work on MacBook Pros, but am currently stumped. I have a Mid 2015 15" MBP with a 2.2 i7/16gb/256ssd with liquid damage and a cracked LCD panel. The computer would work flawlessly with a half-cracked panel, and stress tested without an issue for hours on end. However, whenever I replace the screen assembly with a new replacement, the computer will immediately freeze upon booting into the home screen....
Chosen Solution So, I spilled a liquid on my late 2010 MacBook Air. Between the liquid and the age, i know its got no warranty. As soon as i spilled it, i shut down and let it dry out (big ziploc and rice) until i could get the pentalobe screwdriver to open it up. before opening it up, i wanted to see if the non-invasive drying worked. it starts up, but not by pressing the power button....
Chosen Solution The digitizer stopped working on one side of my XR so I replaced it with one from this site. Since doing that I’ve noticed it freaks out occasionally with lots of flickering and and sometimes ghost touches. I realized it does it whenever I’m on LTE and not Wifi. I have disconnected and reconnected the battery, digitizer and lcd connections several times with no luck. Any ideas? Did you disconnect the battery before you unhooked the connections for the screen?...
Chosen Solution Hey, I like to repair my Galaxy S3 I9305 device. There is no actual guide for the repair. Does anybody know whether it is the same way as the I9300? They are the same. Only differences are the motherboard and the antenna module. I’ve seen a lot of people swapping those screens, you’ll be fine without issues! EDIT: If we are talking about the front glass**** The LCD are different and the way the phone is built too....
Chosen Solution Just replaced a screen and a front camera flex. Now its stuck on the white apple logo screen try replugging the flex cables of the hardware that you replaced, improper connection seating in iphones causes boot loops and other problems as well as improper screw placements.
Chosen Solution Hello community! Ever since some time ago my switch started acting really weird. If I charge it to 100 %, the battery indicator will go down to 1 % in a matter of not even one minute, and stay that way for a short time. Then it will just jump up and down, giving me a low battery indication. I already replaced the battery with a new one, and did some other stuff like leaving the switch on the charger for some time, but nothing really helped....
Chosen Solution Hi I recently replaced the battery in my iPhone 6 because when I was removing the old one, the glue strip snapped and I bent the old one getting it out. So now I have a new battery and it won’t charge, it is stuck on “1% charged”. I’ve charged it for a while, I have taken it out, I have re charged it, I have hard reset, I have factory reset, I have taken the battery out and put it back in, I have changed cables, plug, everything but no success....
Chosen Solution My phone is shutting down automatically even the battery showing 70 percent of power. After switched off it is showing 0 percent power and I need to recharge it. what could be the problem? Is it software or hardware? Please help me get rid off this problem. i also had tht prob bro and i cant fix it did u find solution ?
Chosen Solution I’m having issues with my Samsung TV. Model UN60KU6300F. TV was on and was accidentally unplugged from the outlet. Once it got plugged back in, we lost the picture, just a black screen. The backlights are on, no sound or anything. I get absolutely no picture. A few times when turning it on I’ve seen the Samsung Smart TV logo come on the screen for a second or two then disappear, then back to black screen....
Chosen Solution Hi all Can anyone tell me if this is a zener diode or just a normal diode? I’ve measured the part and it’s a sod 323 or sod 323f package. Numers 551. 03. One of these is blown and laptop not switching on. Thanks Physical Specialist what is the motherboard number.? Post an image zooming out and showing the board. Then let us know what the reference designator for the (blown, not similar,0 diode is and mark its location....
Chosen Solution Hi I have problem with turning on my mac after I replaced the keyboard I tried everything eventually it’s turned on but I have to hold the start key and disconnect and connect the cable while I am holding it. When its turn on the fan is on full speed also the battery has an X whenever I disconnect the cable the laptop die I tried SMC rest but still same Thank you an advance....
Chosen Solution How can I fix this problem pheobe Brown if it is just the keyboard that is not responding in that area, you could try a hard reset. If nothing responds at that area, you may be looking at a bad digitizer. For the hard reset try this Confirm the device is powered off. Hold the Power and Home key simultaneously. Release the Power and Home key once the NOOK logo appears....
